Equipment
Jandy's strength shows up on pads that need pumps, valves, heaters, and salt cells running from a single automation controller. We quote Jandy where an integrated build is the goal and service Jandy across the range.
Categories we install
What we put on the pad, and when it’s the right call.
01
Pumps
What it is
The pump moves pool water through the filter and back to the pool. It runs on a schedule to turn the full volume of water over one to two times a day, which is what keeps the chemistry effective.
When to call
Existing pump is loud, hot, leaking at the seal, or the electric bill jumped after it ran continuously. Or the pool is new and the pad hasn't been built yet.
Our install
Sized to the pool's actual gallons and plumbing size, not a spec-sheet default. Variable-speed models are programmed on install. Unions on both sides of the pump so future service does not require a re-plumb.
Our pumps service →02
Filters
What it is
The filter traps the debris the pump moves through it. Three types: sand, cartridge, or diatomaceous earth. Each has a different micron rating, a different maintenance cadence, and a different annual media cost.
When to call
Pressure gauge climbs faster than a backwash schedule can keep up with, or the water stays cloudy after a full chemistry rebalance. Media cost per year has crept above the price of a fresh cartridge.
Our install
Type chosen against the pump size, the debris load in the yard, and the annual media cost, not the sticker. Multi-port valve set correctly, pressure gauge readable from standing height, drain plumbed to a place the backwash water can actually go.
Our filters service →03
Heaters
What it is
The heater extends the pool's usable season. Two categories: gas heaters (fast, higher operating cost) and heat pumps (slower to warm, much lower to run). Both raise water temperature to a set point.
When to call
Season is closing in September when it could be running through mid-October. Existing heater throws a fault code, will not fire, or has aged past the repair-vs-replace line.
Our install
Sized against surface area, target rise, and overnight ambient temperature. Gas: gas-line load verified against BTU draw, exhaust clearances observed. Heat pump: dedicated circuit run to the applicable NEC section, bonded to the pool's grid.
Our heaters service →04
Salt chlorine generators
What it is
A salt system produces chlorine on demand by passing pool water through a cell that electrolyzes dissolved salt. The pool still runs on chlorine; the difference is the delivery method and the feel of the water.
When to call
Buying bags of chlorine every week feels like a chore, skin sensitivity to conventional chlorine is a problem, or the pool is being built new and the pad is being specced from scratch.
Our install
Cell sized to the pool's gallons with headroom for shoulder-season runtime. Salt dosed to the target parts-per-million after fill, chlorinator programmed against actual bather load.
Our salt chlorine generators service →
05
Automation
What it is
A pool automation controller runs the pump schedule, heater set point, valve positions, salt cell output, and lighting from one interface: typically a wall panel plus a phone app.
When to call
Managing the pad manually has become the job it was not supposed to be. Or the pool has a heater plus a salt cell plus lighting plus water features and the timer strip cannot coordinate them.
Our install
Configured after the mechanical install so schedules match the pump's variable-speed curve, the heater's warm-up window, and the salt cell's runtime. Home Wi-Fi joined to the controller at commissioning, remote access verified before handoff.
Our automation service →06
Lighting
What it is
Underwater LED lighting sized for the pool's volume and geometry. Color-changing capability is standard on newer fixtures; single-color white is still available where the look wants to stay quiet.
When to call
The pool is new and being wired from scratch, or the existing incandescent niche has failed and the swap-in slot is available for a color LED upgrade.
Our install
Fixture rated to the niche, transformer sized to the run length, GFCI verified at the pad. Bonding continuity checked on the niche and the coping.
Our lighting service →07
Cleaners
What it is
An automated cleaner covers the pool floor, walls, and steps between service visits. Three drive types: suction (runs off the skimmer), pressure (runs off a booster pump), and robotic (self-contained, plugs into an outlet).
When to call
Weekly hand-vacuuming has become the way the pool gets cleaned, or the existing cleaner is not covering the walls and steps the way it used to.
Our install
Type matched to the pool's shape, the debris the yard actually drops, and whether a booster pump is present. Filter or bag sized so servicing it isn't a chore.
Our cleaners service →
Equipment prices
Jandy equipment, and what each model costs.
These are the equipment prices. They cover the equipment itself. Installation is quoted separately and is not part of these figures, tax is not included, and shipping may apply.
Pumps
Inground pumps22 models
| Model | Price | Product | Application | HP / THP | Voltage / phase | Amps / breaker | Manual |
|---|---|---|---|---|---|---|---|
| PHPM.75 | $1,115 | Jandy PlusHP Single Speed Pump, 0.75 HP Max Rated, 230/115 V, Single Phase | PHPM.75 | In-Ground | 0.75 HP | 230/115 V; Phase: Single Phase | Manual for PHPM.75 (opens in a new tab) | |
| FHPM.75 | $855 | Jandy FloPro Single-Speed Residential 0.75 hp 115/230V Single-Phase In-Ground Pool Pump | In-Ground | 0.95 THP | 208–230/115 V; Phase: 1 | Amps: 4.5–4.4 A at 208–230 V; 8.8 A at 115 V; Breaker: 15 A branch fuse rating in manual | Manual for FHPM.75 (opens in a new tab) |
| FHPM1.0-2 | $1,125 | Jandy FloPro Dual-Speed Residential 1 hp 230V Single-Phase In-Ground Pool Pump | In-Ground | 1.14 THP | 230 V; Phase: 1 | Amps: 5.3 A high / 2.2 A low; Breaker: 15 A branch fuse rating in manual | Manual for FHPM1.0-2 (opens in a new tab) |
| FHPM1.0 | $915 | Jandy FloPro Single-Speed Residential 1 hp 115/230V Single-Phase In-Ground Pool Pump | In-Ground | 1.14 THP | 208–230/115 V; Phase: 1 | Amps: 5.4–5.2 A at 208–230 V; 10.3 A at 115 V; Breaker: 15 A branch fuse rating in manual | Manual for FHPM1.0 (opens in a new tab) |
| VSFHP165DVS | $1,560 | Jandy VS FloPro Variable Residential 1.65 hp 115/230V In-Ground Pump, w/SpeedSet Controller | Inground | 1.65 hp | 115/230V | ||
| VSFHP185DV2AS | $1,875 | Jandy VS FloPro Variable Residential 1.85 hp 115/208 to 230V In-Ground Pump, 2 Aux Relays, w/SpeedSet Controller | In-Ground | 1.85 THP | 115 / 208–230V | Amps: 8/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSFHP185DV2AS (opens in a new tab) |
| VSFHP185DV2A | $1,800 | Jandy VS FloPro Variable Residential 1.85 hp 115/230V In-Ground Pump, 2 Aux Relays, w/o Controller | In-Ground | 1.85 THP | 115 / 208–230V; Phase: 1 | Amps: 8/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSFHP185DV2A (opens in a new tab) |
| VSFHP185DV | $1,490 | Jandy VS FloPro Variable Residential 1.85 hp 115/230V In-Ground Pump, w/o Controller | In-Ground | 1.85 hp | 115/230V | ||
| VSFHP185DVS | $1,625 | Jandy VS FloPro Variable Residential 1.85 hp 115/230V In-Ground Pump, w/SpeedSet Controller | In-Ground | 1.85 hp | 115/230V | ||
| VSSHP220DV2AS | $2,175 | Jandy ePump Variable Speed Pump, 2.2 HP, 115/230 V, Single Phase, 2 AUX Relays, with Speedset Controller | VSSHP220DV2AS | In-Ground | 2.2 THP | 115/230 V; Phase: Single Phase | Amps: 10.5/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSSHP220DV2AS (opens in a new tab) |
| VSSHP270DV2AS | $2,455 | Jandy ePump Variable Residential Pump 2.7 hp 115/208 to 230V Single-Phase In-Ground w/SpeedSet Controller | In-Ground | 2.7 THP | 115/208 to 230V; Phase: Single-Phase | Amps: 10.5/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSSHP270DV2AS (opens in a new tab) |
| VSSHP270DV2A | $2,415 | Jandy ePump Variable Residential Pump 2.7 hp 115/230V Single-Phase In-Ground w/o Controller | In-Ground | 2.7 THP | 115/230 V; Phase: 1 | Amps: 10.5/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSSHP270DV2A (opens in a new tab) |
| VSFHP270DV2A | $2,165 | Jandy VS FloPro Variable Residential 2.7 hp 115/230V In-Ground Pump, 2 Aux Relays, w/o Controller | In-Ground | 2.7 THP | 115/230 V; Phase: 1 | Amps: 10.5/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSFHP270DV2A (opens in a new tab) |
| VSFHP270DV2AS | $2,235 | Jandy VS FloPro Variable Residential 2.7 hp 115/230V In-Ground Pump, w/SpeedSet Controller | In-Ground | 2.7 THP | 115/230 V | Amps: 10.5/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSFHP270DV2AS (opens in a new tab) |
| VSPHP270DV2AS | $2,420 | Jandy VS PlusHP Variable Speed Residential 2.7 hp 115/208 to 230V In-Ground Pump w/SpeedSet Controller | Inground | 2.7 THP | 115/208 to 230V | Amps: 10.5/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSPHP270DV2AS (opens in a new tab) |
| VSPHP270DV2A | $2,380 | Jandy VS PlusHP Variable Speed Residential 2.7 hp 115/230V Single-Phase In-Ground Pump w/o Controller | In-Ground | 2.7 THP | 115/230 V; Phase: 1 | Amps: 10.5/16A max (230/115V); Breaker: 15/20A minimum (230/115V) | Manual for VSPHP270DV2A (opens in a new tab) |
| VSSHP3802AS | $2,505 | Jandy ePump Variable Residential Pump 3.8 hp 208 to 230V Single-Phase In-Ground w/SpeedSet Controller | Inground | 3.8 THP | 230 V; Phase: Single-Phase | Amps: 16 A maximum; Breaker: 20 A minimum | Manual for VSSHP3802AS (opens in a new tab) |
| JCP051CTS | $8,600 | Jandy Commerical Polymer Pump, 5 Hp, 208-230 V, Single Phase, With Strainer | JCP051CTS | Inground | 5 Hp | 208-230 V; Phase: Single Phase | ||
| JCP053ATS | $8,420 | Jandy Commerical Polymer Pump, 5 Hp, 208-230/460 V, Three Phase, With Strainer | Jcp153Atn | JCP053ATS | Inground | 5 Hp | 208-230/460 V; Phase: Three Phase | ||
| SHPF5.0-3PH | $3,680 | Jandy Stealth Single-Speed Commercial Pool Pump 5 hp 208 to 230/460V Three-Phase In-Ground | In-Ground | 5.75 HP | 208-230/460 V; Phase: 3 | Manual for SHPF5.0-3PH (opens in a new tab) | |
| JCP073ATS | $8,785 | Jandy JCP Residential Pump 7.5 hp 230V Single-Phase In-Ground | Inground | 7.5 hp | 230V; Phase: Single-Phase | ||
| JCP153ATS | $10,220 | Jandy JCP Commercial Pump 15 hp 208 to 230/460V Single-Phase In-Ground | Inground | 15 hp | 208-230/460 V; Phase: Single-Phase | Manual for JCP153ATS (opens in a new tab) |
Filters
Sand filters6 models
| Model | Price | Product | Application | Manual |
|---|---|---|---|---|
| SFTM22-1.5 | $660 | Jandy SFTM Top-Mount Sand Filter 22", 1-1/2" Valve | In-Ground | |
| SFTM24-2.0 | $685 | Jandy SFTM Top-Mount Sand Filter 24", 2" Valve | In-Ground | Manual for SFTM24-2.0 (opens in a new tab) |
| JS100-SM | $1,580 | Jandy JS Series 30" Side-Mount Sand Filter, 4.9 sq. ft, 98 GPM, 47,040 gallons, 50 PSI | JS100-SM | In-Ground | Manual for JS100-SM (opens in a new tab) |
| SFSM100 | $1,480 | Jandy SFSM Side-Mount Sand Filter 30", 100 gpm, 50 psi | In-Ground | Manual for SFSM100 (opens in a new tab) |
| SFSM120 | $2,110 | Jandy SFSM Side-Mount Sand Filter 35.5", 118 gpm, 50 psi | In-Ground | |
| SFSM140F | $2,850 | Jandy SFSM Side-Mount Sand Filter 37", 141 gpm, 50 psi | In-Ground |
Cartridge filters10 models
| Model | Price | Product | Application | Manual |
|---|---|---|---|---|
| CS100 | $725 | Jandy CS 100 sq-ft 100 gpm Single Cartridge Filter In-Ground Residential | In-Ground | Manual for CS100 (opens in a new tab) |
| CS150 | $945 | Jandy CS 150 sq-ft 125 gpm Single Cartridge Filter In-Ground Residential | In-Ground | Manual for CS150 (opens in a new tab) |
| CS200 | $1,120 | Jandy CS 200 sq-ft 125 gpm Single Cartridge Filter In-Ground Residential | In-Ground | Manual for CS200 (opens in a new tab) |
| CS250 | $1,290 | Jandy CS 250 sq-ft 125 gpm Single Cartridge Filter In-Ground Residential | In-Ground | Manual for CS250 (opens in a new tab) |
| CL340 | $1,650 | Jandy CL Cartridge Filter 340 sq-ft 127 gpm Cluster | In-Ground | Manual for CL340 (opens in a new tab) |
| CV340 | $1,595 | Jandy CV Cartridge Filter 340 sq-ft 127 gpm Cluster In-Ground Commercial | In-Ground | Manual for CV340 (opens in a new tab) |
| CL460 | $1,750 | Jandy CL Cartridge Filter 460 sq-ft 150 gpm Cluster | In-Ground | Manual for CL460 (opens in a new tab) |
| CV460 | $1,720 | Jandy CV Cartridge Filter 460 sq-ft 150 gpm Cluster In-Ground Commercial | In-Ground | Manual for CV460 (opens in a new tab) |
| CL580 | $2,110 | Jandy CL Cartridge Filter 580 sq-ft 150 gpm Cluster | In-Ground | Manual for CL580 (opens in a new tab) |
| CV580 | $2,125 | Jandy CV Cartridge Filter 580 sq-ft 150 gpm Cluster In-Ground Commercial | In-Ground | Manual for CV580 (opens in a new tab) |
D.E. filters2 models
| Model | Price | Product | Manual |
|---|---|---|---|
| DEV48 | $1,435 | Jandy DEV 48 sq-ft 96 gpm 5 lb DE Filter | Manual for DEV48 (opens in a new tab) |
| DEV60 | $1,585 | Jandy DEV 60 sq-ft 120 gpm 6 lb DE Filter | Manual for DEV60 (opens in a new tab) |
Heaters
Heat pumps3 models
| Model | Price | Product | Application | BTU / kW | Voltage / phase |
|---|---|---|---|---|---|
| JRT2000R | $5,000 | Jandy VersaTemp Pool Heat Pump COP 6.4 230V 103K BTU Heat/Cool Single-Phase 20 to 70 gpm | In-Ground | 103,000 BTU/h | 208/230 V; Phase: Single-Phase |
| JRT2500R | $5,570 | Jandy VersaTemp Pool Heat Pump COP 6.5 230V 116K BTU Heat/Cool Single-Phase 20 to 70 gpm | In-Ground | 116,000 BTU/h | 5 230V; Phase: Single-Phase |
| JRT3000R | $6,120 | Jandy VersaTemp Pool Heat Pump COP 6.5 230V 130K BTU Heat/Cool Single-Phase 30 to 70 gpm | In-Ground | 130,000 BTU/h | 208/230 V; Phase: Single-Phase |
Gas heaters, natural gas7 models
| Model | Price | Product | Application | BTU / kW | Manual |
|---|---|---|---|---|---|
| JXIQ200NK | $3,800 | Jandy JXiQ Natural Gas Pool Heater 200K BTU, Copper | In-Ground | 200,000 BTU/h | Manual for JXIQ200NK (opens in a new tab) |
| JXI260N | $3,670 | Jandy JXi Pool Heater 260K BTU Natural Gas, Copper | In-Ground | 260,000 BTU/h | Manual for JXI260N (opens in a new tab) |
| JXIQ260NK | $3,870 | Jandy JXiQ Natural Gas Pool Heater 260K BTU, Copper | In-Ground | 260,000 BTU/h | Manual for JXIQ260NK (opens in a new tab) |
| EHE350NC | $12,315 | Jandy Hi-E2 ASME Natural Gas Heater 350000 BTU, Bronze Header | In-Ground | 350,000 BTU/h | Manual for EHE350NC (opens in a new tab) |
| EHE350NS | $13,065 | Jandy Hi-E2 ASME Natural Gas Heater, Bronze Header, 350K BTU, 345 lbs, Cupronickel Exchanger, Max Flow 100 GPM | EHE350NS | In-Ground | 350,000 BTU/h | Manual for EHE350NS (opens in a new tab) |
| JXIQ400NC | $5,715 | Jandy JXiQ ASME Natural Gas Pool Heater 400K BTU, Copper | In-Ground | 400,000 BTU/h | Manual for JXIQ400NC (opens in a new tab) |
| JXIQ400NS | $5,965 | Jandy JXiQ ASME Natural Gas Pool Heater 400K BTU, Cupronickel | In-Ground | 400,000 BTU/h | Manual for JXIQ400NS (opens in a new tab) |
Gas heaters, propane9 models
| Model | Price | Product | Application | BTU / kW | Manual |
|---|---|---|---|---|---|
| JXI200PK | $3,290 | Jandy JXI with VersaFlo Propane Gas Heater, 200K BTU, 137 lbs, Max Flow 100 GPM, Copper Exchanger | JXI200PK | In-Ground | 200,000 BTU/h | Manual for JXI200PK (opens in a new tab) |
| JXIQ200PK | $3,800 | Jandy JXiQ Propane Gas Heater, Versaflo, 200K BTU, Copper Exchanger | JXIQ200PK | In-Ground | 200,000 BTU/h | Manual for JXIQ200PK (opens in a new tab) |
| JXI260P | $3,670 | Jandy JXi Pool Heater 260K BTU Propane Gas, Copper | In-Ground | 260,000 BTU/h | Manual for JXI260P (opens in a new tab) |
| JXIQ260PK | $3,870 | Jandy JXiQ Propane Gas Pool Heater 260K BTU, Copper | In-Ground | 260,000 BTU/h | Manual for JXIQ260PK (opens in a new tab) |
| EHE350PS | $13,065 | Jandy Hi-E2 ASME Propane Gas Heater, Bronze Header, 350K BTU, 345 lbs, Cupronickel Exchanger, Max Flow 100 GPM | EHE350PS | In-Ground | 350,000 BTU/h | Manual for EHE350PS (opens in a new tab) |
| EHE350PC | $12,315 | Jandy Hi-E2 Series ASME Propane Gas Heater, 350K BTU, Copper/Cupronickel Exchanger, Bronze Headers | EHE350PC | In-Ground | 350,000 BTU/h | Manual for EHE350PC (opens in a new tab) |
| JXI400P | $4,720 | Jandy JXi Pool Heater 400K BTU Propane Gas, Copper | In-Ground | 400,000 BTU/h | Manual for JXI400P (opens in a new tab) |
| JXI400PN | $5,100 | Jandy JXi Pool Heater 400K BTU Propane Gas, Cupronickel | In-Ground | 400,000 BTU/h | Manual for JXI400PN (opens in a new tab) |
| JXIQ400PK | $4,830 | Jandy JXiQ Propane Gas Pool Heater 400K BTU, Copper | In-Ground | 400,000 BTU/h | Manual for JXIQ400PK (opens in a new tab) |
Salt chlorine generators
Salt systems2 models
| Model | Price | Product | Voltage / phase | Amps / breaker | Manual |
|---|---|---|---|---|---|
| TRUCLEAR11KU | $1,850 | Jandy TruClear Salt Chlorinator Kit w/ Unions, 35,000 gal | 120/240 V; 50/60 Hz | Amps: 4 A at 120 V / 2 A at 240 V; Breaker: 15 A maximum overcurrent protection | Manual for TRUCLEAR11KU (opens in a new tab) |
| TRUCLEAR11K | $1,800 | Jandy TruClear Salt Chlorinator Kit w/o Unions, 35,000 gal | 120/240 V; 50/60 Hz | Amps: 4 A at 120 V / 2 A at 240 V; Breaker: 15 A maximum overcurrent protection | Manual for TRUCLEAR11K (opens in a new tab) |
Sourcing
We source Jandy equipment through Heritage Pool Supply Group in New Rochelle, NY. We install and service Jandy equipment for residential pools across the New York metro area.
We do not claim authorized-dealer or certified-installer status for any equipment brand. Where those claims matter to you, ask; we will tell you what the actual relationship is.
Other brands we install
Hayward
Hayward covers every category on the pad: pumps, filters, heaters, salt cells, automation, lighting, cleaners. We install across the full line and service Hayward equipment regardless of who put it in.
Read more →
Pentair
Pentair leads on variable-speed pump engineering and on the color LED lighting category. We quote Pentair where a homeowner wants long pump life, a serious lighting spec, or an integrated automation build.
Read more →
Nirvana
Nirvana is a heat-pump specialist rather than a broad-line manufacturer: pool heat pumps and heat-cool systems are the whole catalogue. We quote Nirvana where the decision is electric heat pump versus gas, and we service Nirvana units regardless of who installed them.
Read more →